Welcome to Control.com, the global online community of automation professionals.
Control.com - Nerds in Control
Member Login
Search
Jump to a Date
Sponsored Communities
Cool stuff
Neat Stuff
Visit our shop for nerds in control lifestyle products.
Thermal Overload
The threads that wouldn't die...
- PC reliability?
- Windows, real time
- PID loops
- PCs vs. PLCs
- Replacing people
- MS 'monopoly'?
- Software quality
- Where do we go from here?
- Why pay?
- PC reliability?
- Windows, real time
- PID loops
- PCs vs. PLCs
- Replacing people
- MS 'monopoly'?
- Software quality
- Where do we go from here?
- Why pay?
Fortune
... and furthermore ... I don't like your trousers.
RSS Feed
Use this link to get an RSS feed of the Control.com article flow, for private, non-commercial use only:www.control.com/rss/
To get a personalized feed, become a member at no cost.
Posts from...
Tuesday, July 29, 2008
Generator vibration high when synchronized with network
New Replies:
By hartanto on 29 July, 2008 - 1:41 am -
By hartanto on 29 July, 2008 - 1:41 am -
Thank you Mr. Steve for your comment. We tried it but the vibration is still the same. When...
Operating problem of gas turbine
New Replies:
By CSA on 29 July, 2008 - 1:41 am -
By CSA on 29 July, 2008 - 1:41 am -
Speaking from a different perspective than the operator or the instrument technician or the...
Operating system change
New Replies:
By B. Clemmer on 29 July, 2008 - 1:39 am -
By B. Clemmer on 29 July, 2008 - 1:39 am -
I am currently running Plantscape R320 on a Windows XP machine for testing and have not had any...
MKIV to Laptop communication to capture data from the MKIV panel
New Replies:
By CSA on 29 July, 2008 - 1:37 am -
By CSA on 29 July, 2008 - 1:37 am -
There are two possibilities for the majority of Mark IVs:
1) Connect a laptop to Mark IV's...
We have a permannet magnet, DC motor (rated voltage 36 V, torque 15 Ncm and speed 5 - 40 krpm), with two field coils...
New Replies:
By Randall Moore on 29 July, 2008 - 1:33 am -
By Randall Moore on 29 July, 2008 - 1:33 am -
We should be able to help you.
http://www.carotron.com
Thanks,
Randall...
Gas turbine liquid fuel operation.
New Replies:
By CSA on 29 July, 2008 - 1:30 am -
By CSA on 29 July, 2008 - 1:30 am -
Jojo,
I think there is a heat rate improvement when inlet air cooling is used and there is some...
We decided to make a robot controller or buy a ready robot controller to replace the controller of some old 6 DOF manipulators.
New Replies:
By James Ingraham on 29 July, 2008 - 1:29 am -
By James Ingraham on 29 July, 2008 - 1:29 am -
"Is it possible to use a 6 Axis ready made CNC
controller to control a 6 DOF robot?"
...
I have a question about unequal load sharing of generators.
New Replies:
By CSA on 29 July, 2008 - 1:26 am -
By CSA on 29 July, 2008 - 1:26 am -
Phil,
Are you saying that generators having different droop characteristics can only be operated...
By CTTech on 29 July, 2008 - 12:43 am - As both of you know, this is why we maintain power system operators. They are responsible for...
The latest JimPinto.com - Connections for Growth & Success(TM) No. 252 - 28 July 2008, is on the web...
Curious about MKVI signals that begin with a "#" sign.
New Replies:
By CSA on 29 July, 2008 - 1:22 am -
By CSA on 29 July, 2008 - 1:22 am -
I believe when a # precedes a signal name it refers to the "health" of the signal coming...
By Demigrog on 29 July, 2008 - 1:00 am - The # is used to get the health bit of any signal connected to an I/O point. Clear as mud, right?...
the problem is the distance between the transmitter and the RTU, which is 3000 m....
New Replies:
By wboyes on 29 July, 2008 - 1:21 am -
By wboyes on 29 July, 2008 - 1:21 am -
The most common solution is to install I/I stations every 500 meters. This breaks up the loop into...
What MarkV mode is used to control 10MW steam turbine generator in droop?
New Replies:
By CSA on 29 July, 2008 - 1:15 am -
By CSA on 29 July, 2008 - 1:15 am -
I've been thinking about this even more, and re-reading and then re-reading the original post...
Control valve hunting
New Replies:
By Roni Heru T on 29 July, 2008 - 1:14 am -
By Roni Heru T on 29 July, 2008 - 1:14 am -
I think the condition happens because the positioner has the feedback system, so if the positioner...
Asking opinion on designing a single phase 4 pole AC motor.
Usage of most-significant decimal address to identify a data type.
New Replies:
By JC on 29 July, 2008 - 1:03 am -
By JC on 29 July, 2008 - 1:03 am -
You can think of 10051, 30034, 40021, etc. as register 'Names'. You can subtract an offset from the...
I am looking for this type of unit. The standard units sold by black box, etc have no rating...
New Replies:
By Gopal on 29 July, 2008 - 12:58 am -
By Gopal on 29 July, 2008 - 12:58 am -
We do have a Class I Div II solution for Panel mount Display and Industrial PC with inbuilt KVM...
Ethernet port is not operational
I have PLC Yaskawa Memocon-SC U84. But I haven't any software and cable to connect from PLC to PC.
New Replies:
By sonboz on 29 July, 2008 - 12:55 am -
By sonboz on 29 July, 2008 - 12:55 am -
Dear Sir,
I think that if you contact the Yaskawa Company, they can help you.
Best regards,...
AVR having slow response.
New Replies:
By Anonymous on 29 July, 2008 - 12:54 am -
By Anonymous on 29 July, 2008 - 12:54 am -
Thank you for the reply. For your information, I didn't take any step to resolve the problem yet....
Does Dox10 work with SC05-35? What cable to connect between a PC and SC05-35? Where can I find a user's manual?
New Replies:
By icon on 29 July, 2008 - 12:46 am -
By icon on 29 July, 2008 - 12:46 am -
Hi,
Maybe I can help you. Please contact me at ceo at iconsystems. pk...
Would u suggest any institution for embedded systems in hyderabad?
New Replies:
By Narayana Raju S on 29 July, 2008 - 12:44 am -
By Narayana Raju S on 29 July, 2008 - 12:44 am -
Hi Suresh,
I heard, very soon there is a group of people planning to start a startup company and...
Few months back we had a flash over on the surge arrestor on primary side of power transformer...
New Replies:
By Otpidus on 29 July, 2008 - 12:43 am -
By Otpidus on 29 July, 2008 - 12:43 am -
Power transformers normally experience huge surges during switching on. You have not mentioned...
Can we use 3 way globe control valve in Bio-gas line?
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2008 Control Technology Corporation. All rights reserved.
Our Advertisers
Help keep our servers running...
Patronize our advertisers!
Patronize our advertisers!