Control.com - Nerds in Control
Select Page: 1
Control.com member...
Member Information and Posts by Ayed |
We have in our gas turbine frame 7E a problem of failure to start due to starting clutch disengage.
New Replies:
is this type of clutches recommended from GE?
does it need to configure with MRK V and VI?
i...
Exhaust temperature alarm activated at startup
New Replies:
IGV and first row of compressor were cleaned by maintenance and then the unit was started up....
We experienced a tripping on Exhaust Over Temperature High at 74 to 78% Speed for GTG Unit No. 9 GE...
Dear;
The main problem why did we receive exhaust over temperature alarm?
We do not have any...
We are looking what is the suitable facility to purge these vessels in order to attend the thickness measurement and relief valve calibration.
need to select a new vent pipe line blower
New Replies:
would you please tell me the require information for calculation the performance of the blower.
i...
thanks for your information i will conduct site inspection and com by result.
Thanks and...
calculation of the Lube oil Mist separator blower
What right procedure of calibration for heat detectors and what type of heat detectors (principle of operation) are normally used in GE Frame6 and what is the triggering limit.
New Replies:
i am sorry to write this because i didn't find the way to send you mail Individually.
i want to...
i need what are the most important factors
unit trip after stop command
We have gas turbine of frame 7E. and MRK V is the controller.
Could you please tell me why the Exhaust
Could you please tell me why the Exhaust
New Replies:
Dear Sir;
this is my E-mail address harthiam@marafiq.com.sa...
What is the cause of axial movement on the gas turbine?
What is the difference between loading and unloading bearings?
What is the difference between loading and unloading bearings?
change over from Gas firing to light fuel oil mode before unit reaches full speed no load
New Replies:
dear;
my question was very clear.
does the unit change over from gas to LFO before it reaches...
how the spark plug generates spark
how the flame detector detects the flame
how the flame detector detects the flame
how to calculate the power in MW that drives the compressor...
New Replies:
i am still not get how i can calculate the power that drives the compressor.
i need the equation.
...
Why the Exhaust temperature (TTXM) should not exceed 400 degree Celsius during unit warm-up period?
kindly i need the start up sequence.
why the speed during start up is reduced before firing
New Replies:
Dear Rokan Uddin;
regarding to your question which is about the bleed valves
in our site our...
Why the speed does not increase when the fuel increase?
how the purging process is done during change over the fuel in GE frame 7EA?
New Replies:
in fact we have two types of turbine
first frame 7E and this unit has gas purge valve.
...
the unite is frame 7EA. it not firing on LFO at all.
during Gas turbine start up once the unite reaches 60% of speed the exh. temp.decrease
New Replies:
the unites that we have are GE frame 7E
three stages.
mark V is the controller
...
could you please explain to me how does the seal oil pressure regulator valve in seal oil system
note that the Generator is cooled by H2
note that the Generator is cooled by H2
Cause of axial movement on the gas turbine
find out the load restrictions of Gas turbine.
New Replies:
see please this happen on month ago and UCS control can n't save the data only for 2 weeks.
but...
Select Page: 1
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2013 Nerds in Control, LLC. All rights reserved.
Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.
Fortune
Who's on first?
