Select Page: 1
Control.com member...
Member Information and Posts by msalem73
User Picture
Topic: Sensor technologies.
from the Instrument department...
ABB Thermocouple Transmitter reading fluctuates
Originally posted by msalem73 on 29 March, 2014 - 6:42 am
Transmitters reading Fluctuating
New Replies:
first off all i am sorry for writing down transmitter model is ABB TH02. the answer of your...
Topic: Computers in manufacturing; also hardware discussion.
from the Instument and control department...
Gas Turbine FRAME9FA IBH Opening at Full Load
Posted by mohamed salem on 4 October, 2013 - 8:32 am
Gas Turbine FRAME9FA IBH is Opening at Full Load
Topic: Power generation equipment control.
from the INSTRUMENT AND CONTROL department...
Gas Turbine FRAME9FA IBH Opening at Full Load
Posted by msalem on 2 October, 2013 - 2:49 pm
Why is gas turbine FRAME 9FA IBH opening at full load?
Topic: Power generation equipment control.
from the Instrumentation and control department...
Back Pressure Control Mode In Toshiba steam turbine D-EHC control system
Posted by Mohamed Salem on 15 April, 2013 - 4:45 pm
What is the Back pressure mode in Toshiba steam turbine ?and what is the running condition for this mode?
Topic: Power generation equipment control.
from the Instrument and control department...
Gas turbine Unit 9FA Alwayes tripped by "LOSS OF FLAME"
Originally posted by Mohamed Salem on 14 September, 2012 - 12:11 pm
GE frame9FA triped by los of flame.
New Replies:
Dear AC, i need to tell you our machine recently we perform Combustion inspection (CI) by GE so...
Dear sir CSA, thanks for your interest. i need to clear my brevious message which is not clear...
Dear CSA First I need to thanks you for your fast reply I check again all data and trends for...
Posted by mohamed salem on 20 April, 2012 - 4:01 am
SVS1& SVS2 HMI for Tosmap control system does not display information
Topic: Human-Machine Interface and SCADA.
from the instrument department...
TOSMAP Toshiba control system problem in SVS1&2
Posted by Mohamed salem on 13 April, 2012 - 1:19 am
problem in Toshiba HMI SVS1&2 while calling a logic.
Topic: Human-Machine Interface and SCADA.
from the Instrument department...
Alarm viewer not working in HMI
Originally posted by Mohamed Salem on 30 January, 2012 - 2:38 pm
Alarm viewer not working in HMI
New Replies:
Dear sir, i need to inform u i didnt have backup of E:\Site and I checked the configuration file...
Topic: Power generation equipment control.
from the Instrument control department...
Smarttrak is suddenly close during in service
Posted by Mohamed salem on 27 January, 2012 - 1:24 pm
Problem with HP/IP turbine hydraulic system
Topic: Power generation equipment control.
from the instrument and control department...
Wobbe index alarm and unit trip
Originally posted by mohamed salem on 8 January, 2012 - 2:07 pm
wobbe index alarm
New Replies:
Dear sir thanks for your replay after i checked the logic i found that the value of wobbe index...
Topic: Power generation equipment control.
from the Power department...
Problem in cimplicity point on screen
Originally posted by Mohamed salem on 26 December, 2011 - 3:26 pm
Displaying differential pressure reading in cimplicty version is 6.1
New Replies:
Hi sir, Sorry for late to reply to your message i checked the expression which i am wrote to...
Topic: Human-Machine Interface and SCADA.
from the Software Engineering department...
Problem in cimplicity point on screen.cimplicty version is 6.1
Posted by Mohamed Salem on 21 December, 2011 - 10:00 am
Problem in cimplicity point on HMI screen
Topic: Power generation equipment control.
from the LFBV calibration department...
GE gas turbine frame 9FA LFBV calibration procedures
Originally posted by msalem73 on 1 November, 2011 - 11:25 am
GE gas turbine frame9FA LFBV calibration procedures and list all signals
New Replies:
Dear CSA After greeting i need to inform u When i asked about the LFBV calibration. i need to...
Dear sir Thank u for your reply but the problem which we are faced is that when start the unit...
Thank you for ur reply sir i tried to open and check the valve as u mention. it was moved by...
Thanks for your reply sir I need to inform u some times we need to Check the behaivior of the...
Topic: Power generation equipment control.
from the Control GE department...
How to Add signal point to cimplicity Diagram?
Originally posted by Mohamed salem on 16 November, 2011 - 3:31 pm
How to Add signal point to cimplicity Diagram?
New Replies:
Dear Gemi Thanks for ur reply we are using Mark6 control system, and cimplicity version 6.1...
Topic: Power generation equipment control.
from the Power Generation department...
Error indication in cimplicity HMI
Posted by Mohamed salem on 23 June, 2011 - 11:20 am
Error indication in cimplicity HMI
Topic: Power generation equipment control.
from the Automation control department...
Error indication in cimplicity HMI
Originally posted by Mohamed salem on 9 June, 2011 - 12:26 pm
Incorrect indication in cimplicity for fuel gas vent valve L33VG4
New Replies:
Hi sir I am sorry for that i don't know the rules of this forum that is the truth, if you need...
Topic: Human-Machine Interface and SCADA.
from the Cimplicity department...
Signal indication does not appear in Cimplicity
Posted by GE on 1 June, 2011 - 3:45 pm
Signal indication does not appear in Cimplicity
Topic: Power generation equipment control.
from the instrument and control department...
How to open SRV force?
Originally posted by Mohamed Salem on 20 May, 2011 - 5:41 am
GE frame 9fa During maintenance we need to open the following items manually
New Replies:
> We don't know if you have a Mark V or a Mark VI or a Mark VIe. > But, if you need a...
Topic: Power generation equipment control.
from the Engineer department...
Mark 6 Diagnostic Alarm
Posted by Mohamed Salem on 20 April, 2011 - 11:24 am
Need help to diagnose an alarm on Mark 6 control system
Topic: Power generation equipment control.
from the control department...
CimView error message
Posted by Mohamed Salem on 15 April, 2011 - 4:28 pm
Error message in operator Account
Topic: Power generation equipment control.
from the Gas turbine fram 9fa department...
inlet guide vane control fault trip
Posted by GE on 25 March, 2011 - 1:41 am
inlet guide vane control fault trip
Select Page: 1
 
 

Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2014 Nerds in Control, LLC. All rights reserved.

Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.


Fortune
"Spare no expense to save money on this one."
-- Samuel Goldwyn
Advertise here
Advertisement
our advertisers
Help keep our servers running...
Patronize our advertisers!
Visit our Post Archive