Discussions from the world's leading forum on Industrial Control -- Control.com.en-ushttp://www.control.com/Subject to the rights expressly reserved to others under our Legal Notices at http://www.control.com/about.php#legal, this content and the compilation thereof is Copyright 1999-2010 Nerds in Control, LLC. All rights reserved.Thu, 02 Sep 2010 20:08:06 -0400http://www.ctc-control.com/Web-enabled automation to link industrial control and enterprise IT in real time.http://www.ctc-control.com/http://www.control.com/thread/1283437730#1283462551Wanted to find out if one can put new function blocks numbers in between ones that have already been programmed in a BRC 400 redundant control array.( in the same segment)http://www.control.com/thread/1283437730#1283462551http://www.control.com/thread/1282112977#1283458325 characteristics of slip ring motor http://www.control.com/thread/1282112977#1283458325http://www.control.com/thread/1276349080#1283458230Confusion about those protocols!!http://www.control.com/thread/1276349080#1283458230http://www.control.com/thread/1260839062#1283458154In LM 2500 gas turbine if VSV goes out of schedule how to shut down the engine without engine stall?http://www.control.com/thread/1260839062#1283458154http://www.control.com/thread/1283260003#1283454804Difficulties in synchronizing grab crate close and hold motions http://www.control.com/thread/1283260003#1283454804http://www.control.com/thread/1283260003#1283448441Difficulties in synchronizing grab crate close and hold motions http://www.control.com/thread/1283260003#1283448441http://www.control.com/thread/1282112977#1283441852 characteristics of slip ring motor http://www.control.com/thread/1282112977#1283441852http://www.control.com/thread/1283371336#1283438506Is any rule of thumb that is used to define an alarms reset value or hysteresis?http://www.control.com/thread/1283371336#1283438506http://www.control.com/thread/1283437730Wanted to find out if one can put new function blocks numbers in between ones that have already been programmed in a BRC 400 redundant control array.( in the same segment)http://www.control.com/thread/1283437730http://www.control.com/thread/1282897699#1283437438Connecting an AC450 Node to a new Siemens S7-400 system using VIP (TCP/IP).http://www.control.com/thread/1282897699#1283437438http://www.control.com/thread/1282897699#1283431280Connecting an AC450 Node to a new Siemens S7-400 system using VIP (TCP/IP).http://www.control.com/thread/1282897699#1283431280http://www.control.com/thread/1283198443#1283426457PLC/DAC with 24 bit resolution Voltage I/Ohttp://www.control.com/thread/1283198443#1283426457http://www.control.com/thread/1282897699#1283420662Connecting an AC450 Node to a new Siemens S7-400 system using VIP (TCP/IP).http://www.control.com/thread/1282897699#1283420662http://www.control.com/thread/1283352363#1283417672Two questions on the theory of Laplace and Fourier transforms.http://www.control.com/thread/1283352363#1283417672http://www.control.com/thread/1283352363#1283415497Two questions on the theory of Laplace and Fourier transforms.http://www.control.com/thread/1283352363#1283415497http://www.control.com/thread/1283414473Using Microsoft Access or Open Office with modbus link to switch repeaters on applicable networks for Simocode.http://www.control.com/thread/1283414473http://www.control.com/thread/1283260003#1283411175Difficulties in synchronizing grab crate close and hold motions http://www.control.com/thread/1283260003#1283411175http://www.control.com/thread/1283238064#1283409918What's the best practice in measuring condenser level in absolute vacuum conditions?http://www.control.com/thread/1283238064#1283409918http://www.control.com/thread/1283403115looking for modem GPRS protocol 101/104 unbalanced and DNP 3http://www.control.com/thread/1283403115http://www.control.com/thread/1283362099#1283393387Looking for a 4-20 mA signal duplicatorhttp://www.control.com/thread/1283362099#1283393387http://www.control.com/thread/1278911279#1283391618small pool fire was caused by lube oil possibly leaked out from 2nd bearing oil baffle. Looking for cause of the leakage.http://www.control.com/thread/1278911279#1283391618http://www.control.com/thread/1272373657#1283388305I have a PLC that I am trying to communicate alarms to an annunciator. http://www.control.com/thread/1272373657#1283388305http://www.control.com/thread/1283387886defining the 6 terminals of my encoder is required http://www.control.com/thread/1283387886http://www.control.com/thread/1283362099#1283384831Looking for a 4-20 mA signal duplicatorhttp://www.control.com/thread/1283362099#1283384831http://www.control.com/thread/1026240724#1283383183How to check quality of thermocouple?http://www.control.com/thread/1026240724#1283383183http://www.control.com/thread/1026221257#1283382700Matlab Cannot recognize my parallel porthttp://www.control.com/thread/1026221257#1283382700http://www.control.com/thread/1283371336#1283382560Is any rule of thumb that is used to define an alarms reset value or hysteresis?http://www.control.com/thread/1283371336#1283382560http://www.control.com/thread/1283362099#1283379663Looking for a 4-20 mA signal duplicatorhttp://www.control.com/thread/1283362099#1283379663http://www.control.com/thread/1283379131Asking what exactly VARS is and how it pertains to the power system.http://www.control.com/thread/1283379131http://www.control.com/thread/1283370622#1283377646An easy alternative to 40 pages pf tables and calculations.http://www.control.com/thread/1283370622#1283377646