Control.com - Nerds in Control
Communication over Ethernet from Power Meter to remote server
New Replies:
Tony,
It's an option, but not necessarily secure and usually not cheap. If it's just plain old...
By Tony on 3 April, 2013 - 3:45 am -
Hi
Why not to add a GPRS IP Modem to the Meter, then its data will be sent to Server through GSM...
By Richard on 26 March, 2013 - 11:23 am -
Hi,
www.fieldserver.com has a Modbus RTU to XML over http which will be perfect for you...
Hi Al,
Generically, what you are likely looking for is a Serial-to-Ethernet converter. This is a...
Hi,
Sounds like our product "Netbiter" will suit your needs.
Have a look at:
...
By Darrin Hansen on 22 March, 2013 - 8:52 am -
Hi -
My first comment would be because you apparently have only Modbus RTU at the moment, you'll...
where will I get the complete manual for DeltaV?
New Replies:
By Jo-NathanBSCHE on 2 April, 2013 - 12:11 pm -
In response to your need for a DeltaV Manual. I am very new to C+A and I have found and been using...
MODBUS Address - how to identify?
New Replies:
By Lynn August Linse on 1 April, 2013 - 1:22 pm -
Technically, you are also supposed to watch for time-gaps in the bytes. The serial line should be...
Thank you very much David.
Thanks again for the swift response too.
So that means, I start...
The Modbus Standard Modbus over Serial Line V1.02 (downloadable for free at Modbus.org) says:
...
Looking to explore industrial communication protocols: rf, microwave and optical
contelec PL302- how does it work?
Should I picked Cast Coil or VPI type Transformer for my project?
who can help us? we need the LEA instruction manual for alstom p320.
Modbus Communication Problem.
New Replies:
By Bruce on 25 March, 2013 - 10:21 pm -
Re: More over, looks like ASCII transmission mode.
your TX request should finish with...
By dudy on 21 March, 2013 - 10:02 am -
hello,
if you look your tx message,packet N°5 "0A" hexadecimal value, means you are...
By Lynn August Linse on 21 March, 2013 - 9:46 am -
Check with the device documentation. I suspect if you poll for 1 register, then your master will be...
I need your advice on which field would lead me to enter the oil and gas industry.
New Replies:
By Joe on 22 March, 2013 - 8:20 pm -
Thanks Rushi and Rob.
So I presume both of you guys pursued further studies/earning degrees...
By Rushi Shroff on 22 March, 2013 - 8:41 am -
Hi,
The shift should be smooth.I myself was a web programmer in IT boom period and later lost the...
By Rob on 22 March, 2013 - 12:39 am -
If you already have a software degree or equivalent, then you are every bit as (and possibly more)...
Thanks again....
By Rob on 21 March, 2013 - 6:19 am -
Hi Bob,
As an ex COBOL programmer - I guess its hard to explain. For my part, I kinda fell into...
By Bob Peterson on 20 March, 2013 - 10:33 pm -
computer engineering is closer to control engineering than run of the mill IT stuff. I can believe...
Hi there Bob,
I appreciate your input.
Just to answer your question, I am a computer...
By Bob Peterson on 20 March, 2013 - 9:42 am -
Just curious.
How does one go from IT support to controls engineer?
The skills are...
Understanding how baseload and swing turbines are loaded.
The latest JimPinto.com - 19 March 2013 is on the web
Suppliers of GULDE control valves.
New Replies:
By hfuhr on 18 March, 2013 - 2:52 am -
Gulde is part of EMERSON Process Management
Please contact the german guys at
...
electricity and Magnetism in MOTION CONTROL
Learning about different aspects of automation and gaps in learning
New Replies:
By Walt Boyes on 16 March, 2013 - 4:22 pm -
Begging your pardon, but I define a fieldbus as a digital connection from a field dev ice to a...
By Bob Peterson on 15 March, 2013 - 5:13 pm -
> On the tech side, Modbus is not a fieldbus.
No, but it is not unheard of for it to be used...
the statement "it seems to be the least used of the type behind Canbus, DeviceNet, and...
By Steve Myres on 15 March, 2013 - 11:51 am -
Actually, Profibus is LESS finicky than DeviceNet, even with vastly superior performance specs. ...
By Walt Boyes on 15 March, 2013 - 9:29 am -
Just a minor correction, Bruce, before the Profi boys come looking for you. Profibus is the third...
By Ed W on 14 March, 2013 - 10:55 pm -
Unless you are a person who does a wide verity of installations and not operations, you may not run...
Profibus is a very minor technique in a very large field - I am also 66+ and have never come...
By On looker on 14 March, 2013 - 2:44 pm -
What's profibus? another communication protocol.
I have now come to the understanding, that most...
By Joe E. on 14 March, 2013 - 1:52 pm -
Plenty of facilities don't have any Siemens hardware at all. The engineers would, therefore, never...
from the Instrumentation department...
Why use HART Protocol rather than Fieldbus in some applications?Why HART Protocol is used in DCS rather than Fieldbus in some applications?
New Replies:
By Jonas Berge on 16 March, 2013 - 2:19 pm -
HART goes hand in hand with hardwired 4-20 mA. 4-20 mA is used for control. HART is used for device...
Applications of television and radar in automation
New Replies:
By Walt Boyes on 15 March, 2013 - 9:34 am -
Well, there are three types of radar-based level sensors commonly used in automation: guided wave,...
Latest Jim Pinto article Mobile Devices in Automation
New Replies:
By pvbrowser on 15 March, 2013 - 3:52 am -
The modern mobile devices are nothing else than normal computers with a small display and a touch...
By Curt Wuollet on 14 March, 2013 - 2:18 pm -
Hi Jim
Exactly as predicted when OSS and 21st century software and hardware gain a foothold.
...
Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Please read those terms and conditions carefully. Subject to the rights expressly reserved to others under Legal Notices, the content of this site and the compilation thereof is © 1999-2013 Nerds in Control, LLC. All rights reserved.
Users of this site are benefiting from open source technologies, including PHP, MySQL and Apache. Be happy.
Fortune
The moving cursor writes, and having written, blinks on.
Servo, stepping motor control, analog & web HMI in one system!
Control.com is the largest Automation community on the web. Learn how to advertise here now...
